The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software allows simple interactive product selection of the entire gearbox and gear-engine system. Cat4CAD facilitates you in selecting and configuring these products, provides you the chance to print out intensive technical data linens, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Input power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty class F insulated motor windings
Class 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and greater torques in smaller sized sizes.
Multiple Input Options: Integral gear motors, in . or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Options: Hollow bores and shrink disks for shaft installation, inch and metric output shafts, mounting pilots and flanges offer an array of design solutions.
UNIBLOCK Housing: For optimum rigidity, universal mounting on five sides or with a torque arm.
Worldwide Engine: Multiple leads and windings for worldwide multi volt/Hz requirements plus modular design to simply accept brakes, encoders or forced cooling.
High efficiency motor design available
Innovative self-locking, self-aligning taper shaft engine connection
Gearbox supplied factory filled up with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple locations (Optional OtN2000)
Double lip seals on heat treated, plunge ground shafts
Shaft mounting choices include tapered bushings designs
This is a comprehensive offering of energy-efficient, right angle helical bevel enclosed gearing. It really is offered as gearmotors and a variety of helical bevel gear reducer Reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, face and flanged configurations. Gearmotors can be found in three phase high efficiency styles through 50 HP and single phase to 5 HP. We offer a variety of input and output shaft choices. Additionally, you will find fixed and variable quickness motors and range of ratios obtainable in this product offering.
Features
Accommodates insight power from ¼ Hp to 75Hp
Torque rankings up to 119,489 in-lbs
Reduction ratios up to 7,500:1
Helical – bevel – helical gear train offers cost effective high and low speed solutions
Up to 94% efficient
Four input options available for all units
Two output flange choices – B5 
and B14
Multiple output shaft interfaces
Vital dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
Heavy Duty Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the growing and varying needs of customers, you can expect an array of Helical Bevel Equipment Reducers. The technological content of our products permits an extraordinary functionality/lifespan ratio. The highly versatile Helical Bevel Gear Reducers we offer are successfully found in a multitude of commercial and civil applications. These are B-Series units which offer excellent value for money and result torque/weight ratio, especially considering that they need very limited servicing. Besides these, our products are available in cast iron (sizes 063 to 163) or aluminium (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for engine coupling, IB with input shaft, CB with compact motor, PB-fitted for electric motor coupling with flexible joint
Casing with feet FC, flange SC and universal UC
Switch on to 90 kW
Gears hardened and tempered with shaved or floor profile
Gearing with 3 reduction stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second reduction stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM evaluation and input and output flanges of grey cast-iron G200 to make sure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, output flange, result shaft, shrink disk, backstop device, protection cover kit, viton oil seals, reinforced result, assemble/disassemble kit
Series EP right angle helical bevel equipment motors offer ratios from 8:1 to 160:1 in three phases or up to 10000:1 in five levels. Motors are available up to 90kW and output torque capability up to 12,300 Nm.
The series EP helical bevel gear motor is designed with integral cast feet for base or end mounting and will be offered with single or dual extended output shafts.
Units are also available because shaft mounted or with output flanges and are designed for installation horizontally or vertically. The units can also be offered with a bolt on torque response bracket and all variants are available possibly motorised or with an input shaft assembly.
Adding to the brand new range of Ever-Power helical equipment motors this product takes benefit of our many years of accumulated design expertise together with the use of high quality materials and elements. The outcome is a number of quickness reducing geared motors providing high load transporting capacities, increased efficiency, calm running and reliability.
Top features of Helical Bevel Gear Motor
Standard motor connection
Ability to fit double oil seals, on input and output shaft since required.
All systems are dimensionally interchangeable with various other major manufacturers.
Units are produced and assembled from a family of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units could be fitted with a backstop module and reducer Units can be installed with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemicals, pharma, packaging, food processing, plastic-type and automation etc.
Key Features:
Sizes: A40-A50-A70
Offered versions: EP – fitted for motor coupling, IEP – with input shaft, CEP – with compact motor
Cases with foot, flange or universal
Switch on to 4,8 Kw
Gears with shaved or floor profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Superb mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in in accordance to DIN 1843
Accessories: torque arm, output flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission device and made up of Y series motor, helical gear,Arc gear and worm gear. The gears are constructed with high wear-resisting alloy materials, specifically and finely processed.
Advantages:
1: Helical-bevel gear two-stage reducer
2: Compact framework, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Small design, small volume, wonderful appearance ,and strong capacity to be overloaded.
6: Precise division and wide selection for transmission ratio.
7: The performance is up to as high as 96% with low energy consumption, strong adaptability and is capable of functioning continually in corrosive or damp environment.
8: All- purpose use, convenient and low-cost maintenance.
9: New seal device, strong adaptability.
10: Varied range of motor combinations, mouting positions and struture projects.